Welcome To customized gift for mom!

bed pillow covers DIY Swing Your Kids Will Love pillow covers farmhouse

customized gift for mom
customized gift for mom
pillow cases home decor
bed pillow covers
bed pillow covers DIY Swing Your Kids Will Love pillow covers farmhouse
Views: 96 Updated: :2020-01-18

Hey friends! Spring has nearly sprung here in North Carolina, thank goodness! We've had a few nice days where our girls have played outside alllllll day long, which as a parent is the best thing ever. They get fresh air, Vitamin D and exercise all at the same time! Andmaybeanother tiny benefit is that I can relax in a rocking chair while I watch them ;) One of the reasons our girls love to spend so much time outside is because of this DIY swing we made for them. They mostly use it to stand and swing, but they can also sit on it and push each otherbed pillow covers, which is cool as well.

Thank you to Mohawk Consumer Products for sponsoring this post.This post contains some affiliate links for your convenience (which means if you make a purchase after clicking a link I will earn a small commission but it won't cost you a penny more)!Click here to read my full disclosure policy.

sofa cushion covers

The idea for this DIY swing came after our girls had been begging for a Swurfer. Swurfers are super cool and are a bit easier to get momentum on because the platform is much more curved, so if you love the idea of this DIY swing but would rather buy it than make it, then definitely check out theSwurfer. That said, our DIY swing version cost us significantly less and it's still a total hit with our kiddos.Read on to learn how to make your own DIY swing for a fraction of the price of a store-bought version.

If you’d like a video overview of this project, click below.

1) First, have your kid(s) stand on the skateboard with a wide stance and mark the outer part of their feet. This will help determine where you want to drill the holes for your rope to go through.

2) Next, drill two holes that are parallel to each other on each end of your skateboard using your markings from step 1 as your guide. Our girls helped with this step :)

3) Use a handsaw to cut your 1 inch dowels to form your handles. We cut ours to match the depth of our skateboard.

4) Drill two holes at the end of each handle (for a total of 4 holes per handle). Make the first hole close to the edge of your handle and the second hole approximately 1/2 inch away from the first hole. Repeat on each end of each handle.

5) If you want to stain your skateboard platform to make it pretty, now is the time to do it. Avery wanted the whole thing to be blue. Attley wanted it to be red. So we compromised with red on the bottom and blue on the top :) We usedBehlen Solar Lux Stain(in Sea Blue and Blood Red) because it's fade and UV resistant and the colors are so vibrant and pretty. We coated it with an outdoor rated polyurethane for extra protection.

6) Cut two lengths of rope long enough to wrap around whatever tree branch you are hanging your swing from. Be sure to leave enough rope to run through your handles and to knot as needed (more on that below).

7) We could not reach our tree branch with a ladder, so we tied a loop knot at the end of each length of rope and hooked a carabiner that held a piece of old scrap rope on it. The scrap rope had another carabiner at the other end of it with washers attached to it (to act as weights). Then we threw the carabiner over the tree branch. We were then able to pull the carabiner down toward the ground, threading the rope over the tree branch as we did. We repeated this step for each length of rope.

8) After we looped the rope over the tree branch, it was time to attach it FIRST to the handles, and then to the skateboard platform itself. We taped the ends of the rope with duct tape to make them easier to thread through the holes. To attach the rope to the handles, you thread the rope down through the inside hole. Next, loop the rope over the handle and then down through the outside hole. Doing it this way will allow you to adjust the height of the handles as your kids growwithouthaving to take the whole swing down to do it.

9) Once the handles are attached, all you have to do it thread the rope through the holes on your skateboard platform, making sure to adjust it to the height that you want it AND making it level as you tie the knots. We tiedsimple overhand knotsunderneath the skateboard platform to secure it. we then removed the duct tape from the rope and used a lighter to burn the ends so they will not fray.

We've had our DIY swing up for over a year and it's holding up perfectly so far! Joe and I even use it from time to time (it's harder than it looks, lol)! Take a look at how it turned out.

Don’t forget to join in on the Virtual Costume Parade this year!? I know some of you are still making your costumes..……but once they’re finished, upload your images to the YOU Made It and LOVE It Flickr account.? Then, I will grab them from that account and will share them here TOMORROW!!!? (The deadline to get the pictures uploaded to flickr is tonight.? Around midnight (MST) or so…? Deal??